injection molding cost calculator

Cost of injection molding parts

In three forms it is important to consider how the costs of injection molding are determined:

• To check if the commodity is competitive on the market,
• To recheck with evolving plastic fabrics, cavities, volumes or press measurements so that we can see if additional benefit is produced and
• To determine whether the molding costs of the out-sourcing manufacturer are appropriate.

[CP_CALCULATED_FIELDS id="6"]

Cost Related To The Injection Molding

To assess molding prices, four basic elements must be analyzed:

• Equipment costs,
• Labour costs,
• Process speeds and
• Tooling costs.

The volume or expenses per cubic inch was not just the expense per pound of raw material when measuring production quality.

If necessary, regrind plastic is good to use as the cost typically amounts to around half of new plastic material.

Typically 18 percent of the sum by weight is the assurance that injection molded part should be safely used. Tests demonstrate, though, that 100% regrind may be of same performance as 100% virgin material with respect to final physical quality.

Despite the usage of hot runner system, the volume of materials that form the runner and the sprue does not reach 18% of the shot by weight. In compliance with this thumb law, only 18% of regrind content is suitable for re-usage.

The clamping tonnage scale of the press is calculated by the lock. It is determined by estimating and multiplying the estimated region of the cavities by a multiplier from 2 to 8, i.e. .the amount of tons needed is to hold the mold closed under injection force.

Regardless of its position, hour prices of injection molding machine or MHR fluctuate, with the Northeast and West being the most expensive regions of the U.S.

The average molding time depends primarily on the course of the cooling process.

The expense of equipment is not typically amortized over a product ‘s lifespan but instead charged as a lump amount for front.

The cost of injection molding is related to many factors, but mainly to the following:

Prices of raw materials

Ask suppliers of raw materials for the price and you can easily calculate the cost. When the injection molding parts are multiplied by the raw materials price and the loss (about 4%) of the injection molding parts, the raw materials cost is calculated;

Costs associated with injection molding

The different injection molding machines have different processing costs per hour.

Assume: A 100 ton plastic injection molding machine has a processing cost of USD 30.00 per hour, so the processing cost per minute is 0.5 USD;

Now you need to find out how long the injection cycle lasts and how many cavities there are in the mold, for this example, we estimate 30 seconds per cycle, then 60 shots in an hour, with 2 cavities.

This means plastic machine processing costs is 30/(60 2 2) + 4, and its injection molding is $0.125 per piece.

Costs related to secondary processes

The suppliers can help with spray / silk printing / plating, if you so request.

Expenses related to packaging

An estimation of the packaging carton / packaging bags and other costs will be based on the injection molding part bulk.

Transportation costs

Each part's transport cost can be calculated based on the shipment cost and the load quantity

Personnel expenses

Due to the omission of the personnel costs in the above costs, the final price should include them.

Revenues

Assuming it is the final and real part, you can decide according to factory conditions; usually anything between 10% and 20%. Taxes are popular with the others...

injection molding parts calculation

Here are some great tips to ensure that your organization’s costs remain as low as possible:

Simplify Your Design

It is not necessary to make a complex, fully dimensioned drawing to design a mould. A simple sketch and word description of each part with the part print can serve as the first step in cost reduction just by reducing CAD work and costs with several simple processes.

To make drill jigs used to make holes in shaped sheet metal parts from glass-reinforced plastic (GRP) laminates, one part of the sample part is usually made after the holes are all drilled in their correct location on the part. There are many kinds of instructions that can be provided for using this tool, whether it is a free-hand sketch or written instructions that specify the part dimensions and quantities of drill bushings that must be used.

Utilize Parts Or Models Which Are Already Available

Essentially, plastics can be described as a replicating material. Because of this, a form is always required, except in special circumstances, such as loft template constructions. The fastest method for replicating a part in plastic is to begin by working with an existing design, such as a model or prototype, and mimicking that design with plastic.

Build New Models That Are Male Shaped

When designing a master model, build it in a way that allows for the quickest duplication (which is most common in a male shape) and on the side of metal that requires the minimal amount of thickness transference.

Adopt Flat Runs-Outs

In maximizing the practicality of flat run-outs, most engineers strongly advise using them once constructed, as they provide the simplest possible way to construct their structures.
We want to advise any team member to simplify the reproduction process by removing all undercuts and loose pieces where possible and simplify the process of replicating shapes with plastics by removing all undercuts and loose fragments.

Adopt Lattice-Type Laminates

Lattice-type laminate structures are almost always better than solid structures. This is because they employ fewer materials, require less labor, and weigh less than solid structures.

Choose Supporting Structures Wisely.

Every type of support structure has its advantages and disadvantages based on how each type of tool is adapted. Wood has the benefits of lightness and low cost, but it does suffer from unreliable dimensional stability. Cast iron is the closest thing to wood in terms of price, and it is readily available, but it can require lengthy, costly machining to turn it into a finished product. Aluminum casts are more expensive than cast iron but can usually be ordered more rapidly and can be machined to a point quicker than iron. Cast steel has the highest strength, costing more and taking a long time to manufacture than other metals.

Fabricated plastic components can bear significant losses due to both the cost of components and the labor incurred. Still, they also offer advantages in terms of size and weight.

Fillers Added

Generally, where large quantities of plastics are required without their strengths, fillers can be used to increase the performance of the plastics materials that are relatively costly.

https://www.plasticmoulds.net/injection-molding-cost-calculator.html?feed_id=284&_unique_id=62c64dc41d297